 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| MITSUBISHI INTELLIGENT POWER MODULES PM25RSB120 FLAT-BASE TYPE INSULATED PACKAGE A B M AD S S S P AA 5678 9 11 13 15 17 19 N P 12 3 4 J B 10 12 14 16 18 AB (15 TYP.) D C K N U AD T - DIA. (4 TYP.) Z E U V W H H G W - DIA. (4 TYP.) 1. V UPC 2. UFO 3. U P 4. V UPI 5. VVPC 6. VFO 7. V P 8. V VPI 9. V WPC 10. WFO 11. WP 12. V WPI 13. V NC 14. V NI 15. B R 16. U N 17. V N 18. WN 19. FO 0.5 MM SQ. PIN (19 TYP.) .250 TAB (6 TYP.) X Q L AC V F R Y V V WPC WP W FO V WPI V VPC VP V FO VUPC UP UFO V UPI V VPI VNC WN VNI UN FO BR VN Description: Mitsubishi Intelligent Power Modules are isolated base modules designed for power switching applications operating at frequencies to 20 kHz. Built-in control circuits provide optimum gate drive and protection for the IGBT and free-wheel diode power devices. Features: Complete Output Power Circuit Gate Drive Circuit Protection Logic - Short Circuit - Over Current - Over Temperature - Under Voltage V CC V CC V CC V CC V CC V CC GND GND GND GND GND GND GND GND GND GND GND GND GND GND OUT OUT OUT OUT OUT OUT B N W V U OUT TEMP SI SI SI SI SI SI SI V CC FO FO FO FO FO FO FO IN IN IN IN IN IN IN P Outline Drawing and Circuit Diagram Dimensions A B C D E F G H J K L M N P Inches 3.96 0.04 3.48 0.02 2.76 0.04 2.30 0.02 1.191 0.02 0.83 0.75 0.73 0.71 0.69 0.67 0.581 0.541 0.541 Millimeters 100.5 1.0 88.5 0.5 70.0 1.0 58.5 0.5 30.25 0.5 21.0 19.0 18.5 18.0 17.5 17.0 14.76 13.75 13.74 Dimensions Q R S T U V W X Y Z AA AB AC AD Inches 0.41 0.39 Millimeters 10.5 10.0 0.394 0.010 10.00 0.25 0.39 Dia. 0.364 0.24 0.18 Dia. 0.16 0.12 0.88 0.02 0.086 0.02 0.079 0.010 0.06 0.01 0.02 Dia. 10.0 9.25 6.0 Dia. 4.5 4.0 3.0 2.25 0.5 2.18 0.5 2.00 0.25 1.5 0.25 0.5 Applications: Inverters UPS Motion/Servo Control Power Supplies Ordering Information: Example: Select the complete part number from the table below -i.e. PM25RSB120 is a 1200V, 25 Ampere Intelligent Power Module. Type PM Current Rating Amperes 25 VCES Volts (x 10) 120 Sep.1998 MITSUBISHI INTELLIGENT POWER MODULES PM25RSB120 FLAT-BASE TYPE INSULATED PACKAGE Absolute Maximum Ratings, Tj = 25C unless otherwise specified Ratings Power Device Junction Temperature Storage Temperature Case Operating Temperature Mounting Torque, M4 Mounting Screws Module Weight (Typical) Supply Voltage Protected by OC and SC (VD = 13.5 - 16.5V, Inverter Part, Tj = 125C) Isolation Voltage (Main Terminal to Baseplate, AC 1 min.) Symbol Tj Tstg TC -- -- VCC(prot.) Viso PM25RSB120 -20 to 150 -40 to 125 -20 to 100 0.98 ~ 1.47 330 800 2500 Units C C C N*m Grams Volts Vrms Control Sector Supply Voltage (Applied between VUP1-VUPC, VVP1-VVPC, VWP1-VWPC, VN1-VNC) Input Voltage (Applied between UP-VUPC, VP-VVPC, WP-VWPC, UN * VN * WN * Br-VNC) Fault Output Supply Voltage Applied between (UFO-VUPC, VFO-VVPC, WFO-VWPC, FO-VNC) Fault Output Current (Sink Current at UFO, VFO, WFO and FO Terminal) VD VCIN VFO IFO 20 20 20 20 Volts Volts Volts mA IGBT Inverter Sector Collector-Emitter Voltage (VD = 15V, VCIN = 15V) Collector Current, (TC = 25C) Peak Collector Current, (TC = 25C) Supply Voltage (Applied between P - N) Supply Voltage, Surge (Applied between P - N) Collector Dissipation VCES IC ICP VCC VCC(surge) PC 1200 25 50 900 1000 132 Volts Amperes Amperes Volts Volts Watts Brake Sector Collector-Emitter Voltage Collector Current, (TC = 25C) Peak Collector Current, (TC = 25C) Supply Voltage (Applied between P - N) Supply Voltage, Surge (Applied between P - N) Collector Dissipation Diode Forward Current Diode DC Reverse Voltage VCES IC ICP VCC VCC(surge) PC IF VR(DC) 1200 10 20 900 1000 62 10 1200 Volts Amperes Amperes Volts Volts Watts Amperes Volts Sep.1998 MITSUBISHI INTELLIGENT POWER MODULES PM25RSB120 FLAT-BASE TYPE INSULATED PACKAGE Electrical and Mechanical Characteristics, Tj = 25C unless otherwise specified Characteristics Symbol Test Conditions Min. Typ. Max. Units Control Sector Over Current Trip Level Inverter Part Over Current Trip Level Brake Part Short Circuit Trip Level Inverter Part Short Circuit Trip Level Brake Part Over Current Delay Time Over Temperature Protection toff(OC) OT OTr Supply Circuit Under Voltage Protection UV UVr Supply Voltage VD ID Vth(on) Vth(off) fPWM IFO(H) IFO(L) Minimum Fault Output Pulse Width tFO VD = 15V Trip Level Reset Level Trip Level Reset Level Applied between VUP1-VUPC, VVP1-VVPC, VWP1-VWPC, VN1-VNC Circuit Current VD = 15V, VCIN = 15V, VN1-VNC VD = 15V, VCIN = 15V, VXP1-VXPC Input ON Threshold Voltage Input OFF Threshold Voltage Applied between UP-VUPC, VP-VVPC, WP-VWPC, UN * VN * WN * Br-VNC PWM Input Frequency Fault Output Current 3- Sinusoidal VD = 15V, VFO = 15V VD = 15V, VFO = 15V VD = 15V -- -- -- 1.0 15 -- 10 1.8 20 0.01 15 -- kHz mA mA ms -- -- 1.2 1.7 44 13 1.5 2.0 60 18 1.8 2.3 mA mA Volts Volts SC -20C T 125C, VD = 15V OC -20C T 125C, VD = 15V 32 15 -- -- -- 111 -- 11.5 -- 13.5 62 30 101 41 10 118 100 12.0 12.5 15 -- -- -- -- -- 125 -- 12.5 -- 16.5 Amperes Amperes Amperes Amperes s C C Volts Volts Volts Sep.1998 MITSUBISHI INTELLIGENT POWER MODULES PM25RSB120 FLAT-BASE TYPE INSULATED PACKAGE Electrical and Mechanical Characteristics, Tj = 25C unless otherwise specified Characteristics Symbol Test Conditions Min. Typ. Max. Units IGBT Inverter Sector Collector Cutoff Current ICES VEC VCE(sat) VCE = VCES, Tj = 25C VCE = VCES, Tj = 125C Emitter-Collector Voltage Collector-Emitter Saturation Voltage -IC = 25A, VD = 15V, VCIN = 5V VD = 15V, VCIN = 0V, IC = 25A VD = 15V, VCIN = 0V, IC = 25A, Tj = 125C Inductive Load Switching Times ton trr tC(on) toff tC(off) VD = 15V, VCIN = 0 15V VCC = 600V, IC = 25A Tj = 125C 0.5 -- -- -- -- 1.0 0.15 0.4 2.0 0.7 2.5 0.3 1.0 3.0 1.2 s s s s s -- -- -- -- -- -- -- 2.5 2.5 2.2 1.0 10 3.5 3.5 3.2 mA mA Volts Volts Volts Brake Sector Collector-Emitter Saturation Voltage VCE(sat) VD = 15V, VCIN = 0V, IC = 10A, Tj = 25C VD = 15V, VCIN = 0V, IC = 10A, Tj = 125C Diode Forward Voltage Collector Cutoff Current VFM ICES -IC = 10A, VD = 15V, VCIN = 5V VCE = VCES, Tj = 25C VCE = VCES, Tj = 125C -- -- -- 2.5 -- -- 3.5 1 10 Volts mA mA -- 2.5 3.5 Volts -- 2.8 3.8 Volts Sep.1998 MITSUBISHI INTELLIGENT POWER MODULES PM25RSB120 FLAT-BASE TYPE INSULATED PACKAGE Thermal Characteristics Characteristic Junction to Case Thermal Resistance Symbol Rth(j-c)Q Rth(j-c)F Rth(c-f)Q Rth(c-f)F Contact Thermal Resistance Rth(c-f) Condition Each Inverter IGBT Each Inverter FWDi Each Brake IGBT Each Brake FWDi Case to Fin Per Module, Thermal Grease Applied Min. -- -- -- -- -- Typ. -- -- -- -- -- Max. 0.95 2.5 2.0 2.5 Units C/Watt C/Watt C/Watt C/Watt 0.036 C/Watt Recommended Conditions for Use Characteristic Supply Voltage Symbol VCC VD Input ON Voltage Input OFF Voltage PWM Input Frequency Minimum Dead Time VCIN(on) VCIN(off) fPWM tdead Condition Applied across P-N Terminals Applied between VUP1-VUPC, VN1-VNC, VVP1-VVPC, VWP1-VWPC Applied between UP, VP, WP, UN, VN, WN, Br Using Application Circuit Input Signal 0 ~ 0.8 4.0 ~ VD 5 ~ 20 2.5 Volts Volts kHz s Value 0 ~ 800 15 1.5 Units Volts Volts Sep.1998 MITSUBISHI INTELLIGENT POWER MODULES PM25RSB120 FLAT-BASE TYPE INSULATED PACKAGE Inverter Part SATURATION VOLTAGE CHARACTERISTICS (TYPICAL) COLLECTOR-EMITTER SATURATION VOLTAGE CHARACTERISTICS (TYPICAL) OUTPUT CHARACTERISTICS (TYPICAL) 3.0 COLLECTOR-EMITTER SATURATION VOLTAGE VCE(sat), (VOLTS) SATURATION VOLTAGE VCE(sat), (VOLTS) 3.0 COLLECTOR CURRENT, IC, (AMPERES) 30 25 20 15 10 5 0 0 12 14 16 18 20 0 0.5 1.0 1.5 2.0 2.5 3.0 SUPPLY VOLTAGE, VD, (VOLTS) COLLECTOR-EMITTER VOLTAGE, VCE, (VOLTS) 2.5 2.0 1.5 1.0 0.5 0 0 VD = 15V VCIN = 0V Tj = 25oC Tj = 125oC 2.5 2.0 1.5 1.0 0.5 0 IC = 25A VCIN = 0V Tj = 25oC Tj = 125oC Tj = 25oC VCIN = 0V VD = 17V 15 13 10 20 30 COLLECTOR CURRENT, IC, (AMPERES) SWITCHING TIME VS. COLLECTOR CURRENT (TYPICAL) SWITCHING TIME VS. COLLECTOR CURRENT (TYPICAL) REVERSE RECOVERY CURRENT VS. EMITTER CURRENT (TYPICAL) 101 VCC = 600V VD = 15V SWITCHING TIMES, ton, toff, (s) 101 Inductive Load 101 VCC = 600V VD = 15V Tj = 25oC Tj = 125oC toff SWITCHING TIMES, tc(on), tc(off), (s) Inductive Load Tj = 25oC Tj = 125oC REVERSE RECOVERY TIME, trr, (s) Inductive Load Tj = 25oC Tj = 125oC Irr 100 101 100 ton 100 tc(off) tc(on) 10-1 trr 100 10-1 100 101 COLLECTOR CURRENT, IC, (AMPERES) 102 10-1 100 101 COLLECTOR CURRENT, IC, (AMPERES) 102 10-2 100 101 10-1 102 COLLECTOR REVERSE CURRENT, -IC, (AMPERES) DIODE FORWARD CHARACTERISTICS COLLECTOR REVERSE CURRENT, -IC, (AMPERES) OVER CURRENT TRIP LEVEL VS. SUPPLY VOLTAGE (TYPICAL) OVER CURRENT TRIP LEVEL VS. TEMPERATURE (TYPICAL) 102 140 OVER CURRENT TRIP LEVEL % (NORMALIZED) OVER CURRENT TRIP LEVEL % (NORMALIZED) 140 Tj = 25oC VD = 15V VD = 15V VCIN = 15V Tj = 25oC Tj = 125oC 120 120 100 100 101 80 80 60 0 60 0 100 0.4 0.8 1.2 1.6 2.0 2.4 2.8 EMITTEER-COLLECTOR VOLTAGE, VEC, (VOLTS) 0 12 14 16 18 20 -50 0 50 100 150 SUPPLY VOLTAGE, VD, (VOLTS) JUNCTION TEMPERATURE, Tj, (oC) Sep.1998 REVERSE RECOVERY CURRENT, Irr, (AMPERES) VCC = 600V VD = 15V 102 MITSUBISHI INTELLIGENT POWER MODULES PM25RSB120 FLAT-BASE TYPE INSULATED PACKAGE Inverter Part FAULT OUTPUT PULSE WIDTH VS. TEMPERATURE (TYPICAL) CONTROL SUPPLY VOLTAGE TRIP-RESET LEVEL TEMPERATURE DEPENDENCY (TYPICAL) TRANSIENT THERMAL IMPEDANCE CHARACTERISTICS (Each IGBT) TRANSIENT IMPEDANCE, Zth(j-c), (NORMALIZED VALUE) 140 FAULT OUTPUT PULSE WIDTH % (NORMALIZED) 15 VD = 15V UVt UVr 101 120 UV TRIP-RESET LEVEL, UVt, UVr, (VOLTS) 14 100 100 13 10-1 80 12 60 11 10-2 SINGLE PULSE STANDARD VALUE = Rth(j-c)Q = 0.95oC/W 0 -50 0 50 100 150 JUNCTION TEMPERATURE, Tj, (oC) 0 -50 0 50 100 150 JUNCTION TEMPERATURE, TJ, (oC) 10-3 10-3 10-2 10-1 TIME, (s) 100 101 TRANSIENT THERMAL IMPEDANCE CHARACTERISTICS (Each FWDi) TRANSIENT IMPEDANCE, Zth(j-c), (NORMALIZED VALUE) 101 100 10-1 10-2 SINGLE PULSE STANDARD VALUE = Fth(j-c)F = 2.5oC/W 10-3 10-3 10-2 10-1 TIME, (s) 100 101 Sep.1998 PM25RSB120 MITSUBISHI INTELLIGENT POWER MODULES PM25RSB120 FLAT-BASE TYPE INSULATED PACKAGE Brake Part SATURATION VOLTAGE CHARACTERISTICS (TYPICAL) COLLECTOR-EMITTER SATURATION VOLTAGE CHARACTERISTICS (TYPICAL) OUTPUT CHARACTERISTICS (TYPICAL) 3.0 COLLECTOR-EMITTER SATURATION VOLTAGE VCE(sat), (VOLTS) SATURATION VOLTAGE VCE(sat), (VOLTS) 3.5 3.0 2.5 2.0 1.5 1.0 0.5 0 0 5 COLLECTOR CURRENT, IC, (AMPERES) 15 COLLECTOR CURRENT, IC, (AMPERES) 2.5 2.0 1.5 1.0 0.5 0 10 VD = 15V VCIN = 0V Tj = 25oC Tj = 125oC Tj = 25oC VCIN = 0V 15 10 VD = 17V 13 5 Tj = 25oC IC = 10A 0 20 0 1 2 3 4 COLLECTOR-EMITTER VOLTAGE, VCE, (VOLTS) 0 12 14 16 18 SUPPLY VOLTAGE, VD, (VOLTS) DIODE FORWARD CHARACTERISTICS TRANSIENT IMPEDANCE, Zth(j-c), (NORMALIZED VALUE) TRANSIENT THERMAL IMPEDANCE CHARACTERISTICS (Each IGBT) TRANSIENT THERMAL IMPEDANCE CHARACTERISTICS (Each FWDi) TRANSIENT IMPEDANCE, Zth(j-c), (NORMALIZED VALUE) 102 DIODE FORWARD CURRENT, IF, (AMPERES) 101 101 VD = 15V VCIN = 15V Tj = 25oC Tj = 125oC 100 100 101 10-1 10-1 10-2 SINGLE PULSE STANDARD VALUE = Rth(j-c)Q = 2.0oC/W 10-2 SINGLE PULSE STANDARD VALUE = Fth(j-c)D = 2.5oC/W 100 0 0.4 0.8 1.2 1.6 2.0 DIODE FORWARD VOLTAGE, VF, (VOLTS) 10-3 10-3 10-2 10-1 TIME, (s) 100 101 10-3 10-3 10-2 10-1 TIME, (s) 100 101 Sep.1998 |
Price & Availability of PM25RSB120
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |